|
|
|
Marantz ZS5300
Discrete Amplifier Section (6 X 60 Watts),
Identical Audio Circuits For All 6 Channels,
Party Mode,
Zone Expandable (Total 9 Zones),
Independent Control Over Each Zone,
Matrix Audio Selector,
Compatible With A Variety of Keypads Including Niles And Xantech,
Power Save Function,
High
|
|
Marantz ZS5300 6-Channel Amplifier
The ZS5300 is a 6 channel multi-zone control amplifier designed specifically for an all-in-one solution to custom distributed audio. When combined with a receiver and/or other source components, the ZS5300 transforms your main system into a whole house audio system. Watch a DVD in full surround soun
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mark Levinson No. 431
- Dimensions : 17.75"w × 5.91"h × 20.1"d
- Frequency Response : Within 0.1dB from 20Hz - 20kHz
- Input Connectors : two 3-pin XLR balanced input connectors
- Input Sensitivity - 2.83V Output : 130mV
|
|
Mark Levinson No. 432
- Dimensions : 17.75"w × 7.65"h × 20.1"d
- Frequency Response : Within 0.1dB from 20Hz - 20kHz
- Input Connectors : Two 3-pin XLR balanced input connectors
- Input Sensitivity - 2.83V Output : 130mV
|
|
|
|
Mark Levinson No. 434
- Damping Factor : Greater than 800, 20-20,000Hz at 8 ohms
- Dimensions : 17.75"w × 5.91"h × 20.21"d
- Frequency Response : within 0.2dB from 20 Hz to 20 kHz
- Input Connectors : One 3-pin XLR balanced input connector
- Input Sensitivity - 2.83V Output : 130mV
|
|
Mark Levinson No. 436
- Damping Factor : Greater than 800, 20-20,000Hz at 8 ohms
- Dimensions : 17.75"w × 7.65"h × 20.21"d
- Frequency Response : within 0.2dB from 20 Hz to 20 kHz
- Input Sensitivity - 2.83V Output : 130mV
|
|
|
|
Marsh Sound Designs A200s Amplifier
120 watts x 2 @ 8 ohms
190 watts x 2 @ 4 ohms
High current parallel bipolar power transistors to meet peak current demands
Accepts balanced inputs
|
|
|
|
Marsh Sound Designs A400s Amplifier
200 watts x 2 @ 8 ohms
330 watts x 2 @ 4 ohms
Accepts balanced inputs
High current parallel bipolar power transistors to meet peak current demands
|
|
|
|
|
|
Marsh Sound Designs HT500s
Marsh HT500s 100 Watt 3-Channel Home Theatre Power Amplifier
300 watts,a high-end circuit with very low-noise FET's that are made even more linear by aa balanced, cascoded, complimentary differential input circuit.Servo-controlled, direct-coupled circuitry is used throughout for extremely high re
|
|
|
|
M-Audio Audio Buddy Dual Amplifier
If you’re looking for a whole lot of preamp on a tight budget, you’ll see where this popular product gets its name. Affordability and performance make the Audio Buddy one of the most popular mic preamps in home recording today. You get professional microphone support along with line inputs impedance
|
|
M-Audio Tampa Amplifier
TAMPA is a professional microphone/instrument preamp unlike any other. That's because M-Audio's design team set out to discover just why expensive tube technology sounds so good, and devise a way to land that sound at affordable solid state prices. The result is far beyond tube modeling. It's a whol
|
|
MBL 8006 A
- Sophisticated circuit design
- Sound clarity
- Sensitive sound panorama
|
|
MBL 8011 M
- High-end purist on design
- Highly recommended
- Mono output stages
- High level of quality
|
|
MBL 8011 S
- Four output stages
- Two-way cooling system
- Ground plane layout
- Impressive sound
- High-quality technology
|
|
MBL 9008
- Multi-layer PCB
- DC servo coupling
- Low-induction components
|
|
MBL 9011
- Multi-layer PCB
- Heavy CU planes
- Low-induction MPC
- X-crossed array
|
|
McAlister Audio SE 44 SET AMP
Amazing single ended amplifier. Pure class A tube amp design. Uses 0 global feedback for a very open soundstage. Extremely fast design using horizontal output tubes that have lower harmonic distortion than 811, 300B ,6550, EL34 etc and are more efficient than 300B’s. Minimalist design using point to
|
|
|
|
|
|
|
|
McCormack DNA-125
DNA-125, STEREO Amplifier with output power rating of 125 watts per channel RMS, both channels driven into 8 ohms at less than 1% THD, 200 into 4 ohms.
Input Impedance: 100 kOhms
Input Sensitivity: 1 volt rms
Hum and Noise: better than 98 dB below rated power
Dimensi
|
|
|
|
|
|
|
McCormack DNA-500
- 500 watts per channel
- Input Impedance: 10 kOhms
- Input Sensitivity: 2.25 volt rms
Specifications DNA - 500, STEREO Amplifier with output power rating of 500 watts per channel RMS, both channels driven into 8 ohms at less than 1% THD, 900 watts per chan
|
|
|
|
|
|
|
|
|
|
McIntosh amp
Ive had this amp for about 1 year and love the sound and can't think of any complaints..I use bmw speakers dm640 and they work excellent.
My only complaint is they dont seem to put out 250 watts rms at 8 ohms.cant verifiy that though..
|
|
|
|
|
McIntosh MA6500
Integrated Amplifier
2 x 120/200/250 (8/4/2 ohms)
Wide Power Bandwidth Width with Ultra-Low Distortion
Power Output Meters
|
|
|
|
|
|
|
McIntosh MC1201
- 1200 Watt Mono Power Amplifier
- Double Balanced, Push/Pull Design
- Full Power into 2, 4, or 8 ohms
- 200 Amperes of Output Current
- Low Dielectric Absorption
|
|
|
|
